废旧冰箱拆解聚氨酯泡沫塑料制备PU/PP复合材料

利用废旧冰箱拆解的聚氨酯泡沫塑料(PU)和聚丙烯(PP)、聚丙烯接枝马来酸酐(PP-g-MAH)为原料,采用物理化学回收技术制备PU/PP复合材料。用正交实验法分析PU填充量、PU粒径和PP-g-MAH 3个因素对PU/PP复合材料力学性能影响的显著性。结果表明,PU填充量对PU/PP复合材料拉伸性能有显著影响,对冲击性能和弯曲性能没有显著影响;在本文的实验范围内,PU粒径对PU/PP复合材料的力学性能影响不大;而PP-g-MAH投加量对PU/PP复合材料具有一定的影响。确定的优化工艺配方为:PU 40%;PU粒径选择2.00 mm;PP-g-MAH投加量10%。采用优化工艺制备的PU/PP复合材料的密度为1 042.88 kg/m3;冲击强度为2.9 kJ/m2;拉伸强度为10.30 MPa;拉伸模量为1 100 MPa;弯曲强度为18.5 MPa;弯曲模量为733 MPa。     

基于改性凹凸棒土的强化混凝处理高藻低浊原水工艺

针对水厂低浊高藻水的处理难题,研究了改性凹凸棒土(改性凹土)联合聚合氯化铝(PAC)强化混凝的除藻除浊效果。设计实验原水条件为叶绿素a(chl-a)浓度为98.58~110.35μg/L,浊度(5.6±0.5)NTU。考察了PAC和改性凹土的复配投加量、混凝沉淀时间、pH、投加顺序、搅拌速率等工艺参数对Chl-a和浊度耦合去除效果的影响。结果表明,"PAC+改性凹土"对Chl-a和浊度的去除效果明显优于单投PAC的效果。当PAC投药量12 mg/L,改性凹土投药量10 mg/L,沉淀时间20 min时,对Chl-a和浊度的去除率可分别达到92.5%和89.2%,可至少减少40%的PAC投量,且形成的矾花密实,沉降速度快,去除效率高。最适pH范围为7~8。投加顺序应为先投加改性凹土,混合搅拌转数宜慢速,可控制为50 r/min。     

Prediction of future disposal of end-of-life refrigerators containing CFC-11

The objective of this study was to predict the number of refrigerators containing CFC-11 blown isolation foam and the amount of CFC-11 banked in these refrigerators. By using a Weibull-based survival function, the number of CFC-11 containing and still-functioning refrigerators was estimated to be approximately 1.6 million in 2013 in Turkey. In order to determine the amount of CFC-11 in the isolation foam of these refrigerators, polyurethane (PU) foam samples were taken from a refrigerator manufactured in 1993 and the quantity of CFC-11 was analyzed by a GC-MS. It was determined that 113–195 mg CFC-11/g PU remains in the PU foam depending on the location such as door, sides, top and bottom. Knowing that a mid-sized refrigerator contains 4 kg PU on average, the total amount of PU foam to be disposed of is 6344 tons when the CFC-11 containing refrigerators in Turkey become obsolete in the near future. Furthermore, 717–1237 tons of CFC-11 are expected to be banked in the PU foam of these refrigerators which will exert an equivalent amount of ozone depleting potential (ODP). In addition, the global warming potential will vary between 3.4 and 5.9 million tons of CO₂.     

污水处理移动床生物膜反应器悬浮载体研究进展

介绍了移动床生物膜反应器(MBBR)中悬浮载体的种类和特性,讨论了对其性能的影响因素,总结了当前悬浮载体改性技术及性能评价的方法,并对后续研究提出了建议。     

Development of heat transfer and evaporation model of LNG covered by Hi-Ex foam

Natural gas is a kind of clean, efficient green energy source, which is used widely. Liquefied natural gas (LNG) is produced by cooling natural gas to −161 °C, at which it becomes the liquid. Once LNG was released, fire or explosion would happen when ignition source existed nearby. The high expansion foam (Hi-Ex foam) is believed to quickly blanket on the top of LNG spillage pool and warm the LNG vapor to lower the vapor cloud density at the ground level and raising vapor buoyancy. To identify the physical structure after it contacted with LN₂ and to develop heat transfer model, the small-scale field test with liquid nitrogen (LN₂) was designed. In experiment, three layers including frozen ice layer, frozen Hi-Ex layer and soft layer of Hi-Ex foam were observed at the steady state. By characterizing physical structure of the foam, formulas for calculating the surface of single foam bubble and counting foam film thickness were deduced. The micro heat transfer and evaporation model between cryogenic liquid and Hi-Ex foam was established. Indicating the physical structure of the frozen ice layer, there were a certain number of icicles below it. The heat transfer and evaporation mathematical model between the frozen ice layer and LNG was derived. Combining models above with the heat transfer between LNG, ground and cofferdam, the heat transfer and evaporation mathematical model of LNG covered by Hi-Ex foam was developed eventually. Finally, LN₂ evaporation rate calculated by this model was compared with the measured evaporation rate. The calculated results are 1.2–2.1 times of experimental results, which were acceptable in engineering and proved the model was reliable.     

改性氧化铝微波诱导催化氧化处理高浓度苯酚废水的研究

采用微波诱导催化氧化技术，以改性氧化铝为催化剂，对高浓度模拟苯酚废水进行氧化处理。考察了微波功率、催化剂投加量、H202投加量、废水pH值和微波反应时间等因素对苯酚去除效果的影响。实验结果表明，处理30mL质量浓度为1 100mg/L的苯酚模拟废水，在微波功率500W，催化剂加入量1 g(液固比30∶1)，30％双氧水...     

锆-十六烷基三甲基氯化铵改性活性炭对水中硝酸盐和磷酸盐的吸附特性

采用锆(Zr)和阳离子表面活性剂十六烷基三甲基氯化铵(CTAC)对活性炭进行联合改性,考察了所制备的Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐的吸附去除作用,并探讨了相关的吸附去除机制.结果表明,Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐均具备较好的吸附去除能力.Zr-CTAC改性活性炭对硝酸盐和磷酸盐吸附动力学过程满足准二级动力学模型.Langmuir、Freundlich和Dubinin-Radushkevich(D-R)等温吸附模型可以较好地描述Zr-CTAC改性活性炭对水中硝酸盐的等温吸附过程,Langmuir和D-R等温吸附模型可以较好地描述Zr-CTAC改性活性炭对水中磷酸盐等温吸附过程,通过Langmuir模型计算得到吸附剂对硝酸盐和磷酸盐的最大单位吸附量分别为7.58 mg·g-1和10.9 mg·g-1.高的p H会抑制Zr-CTAC改性活性炭对水中硝酸盐和磷酸盐的吸附.水中共存的Cl-、HCO-3和SO2-4等阴离子均会抑制Zr-CTAC改性活性炭对硝酸盐和磷酸盐的吸附,且对吸附硝酸盐的抑制作用较强而对吸附磷酸盐的抑制作用较弱.水中共存的磷酸盐对Zr-CTAC改性活性炭吸附硝酸盐的抑制作用较强,而水中共存的硝酸盐对Zr-CTAC改性活性炭吸附磷酸盐的抑制作用较弱.1 mol·L-1Na Cl溶液可以使90%左右被吸附到Zr-CTAC改性活性炭表面上的硝酸盐解吸下来.1 mol·L-1的Na OH溶液可以使78%左右被吸附到Zr-CTAC改性活性炭表面上的磷酸盐解吸下来.Zr-CTAC改性活性炭对硝酸盐的吸附机制主要包括阴离子交换作用和静电吸引作用,对磷酸盐的吸附机制主要包括配位体交换作用、阴离子交换作用和静电吸引作用.上述结果说明Zr-CTAC改性活性炭适合作为一种吸附剂去除废水中的硝酸盐和磷酸盐.     

不同运行模式下改良型CAST工艺处理生活污水的除磷性能

实验采用改良型CAST工艺,以生活污水为研究对象,考察了C/P、回流比及温度等不同运行模式对系统除磷性能的影响.结果表明,常温条件下进水C/P由50升至100,系统除磷率均值从15%迅速升至95.6%,除磷性能显著提高;继而降低C/P至75,除磷性能因进水碳源不足再度下降,除磷率均值为51.4%,且长期投加易降解碳源引发系统污泥膨胀并导致污泥大量流失.C/P较低情况下,回流比由25%降低至12.5%,除磷性能提高2.3倍,继续降低回流比至0,除磷性能反而下降;温度实验研究则表明,低温系统(14℃±1℃),除磷率稳定维持在90%以上,而高温短程硝化系统(27℃±1℃)除磷率仅为14.1%,可见低温更有利于系统磷的去除.吸磷小试发现,常温系统污泥以O_2、NO_3~-和NO_2~-为电子受体均能进行吸磷,而低温系统污泥能以O_2、NO_3~-为电子受体进行吸磷,高温系统污泥则仅能以O_2为电子受体进行少量吸磷.此外,实验还发现,系统短期闲置导致的污泥"饥饿"有利于系统除磷率的提高.     

硅藻土负载型非均相芬顿催化剂制备及其降解苯酚的实验研究

以硅藻土为载体,采用直接蒸发法负载铁的氧化物,制备了一种新型负载型非均相芬顿催化剂,通过SEM、EDS和XRD等对催化剂进行了表征,并以苯酚去除率考察了催化剂性能。结果表明:铁氧化物可成功负载于硅藻土上;催化剂制备时最优铁离子浓度和固液质量比分别为0.5 mol/L和1∶10;催化剂重复使用性高,耐酸碱性良好,对苯酚的去除率可达99%以上。催化剂利用了硅藻土优异的物化性质,对难降解有机废水具有良好的应用前景。     

碳酸钙改性硅藻土处理电解锌漂洗废水实验研究

铅锌矿在我国储存量大,电解法生产锌过程中可产生含Zn~(2+)、Pb~(2+)、Cd~(2+)、As5+和Cu~(2+)等重金属离子的漂洗废水。以硅藻土精土为基体,用碳酸钙作为改性剂制备改性硅藻土,对电解锌漂洗废水进行吸附实验研究。结果表明:在反应时间为150 min,碳酸钙改性硅藻土用量为3 g/L,pH为5.46,温度为25℃条件下,对废水进行吸附实验,吸附后废水中的Cu~(2+)和As5+离子浓度低于仪器检测线(0.01 mg/L和0.09 mg/L),Pb~(2+)浓度为0.16 mg/L,吸附后废水中Cu~(2+)、As5+和Pb~(2+)离子浓度均满足GB 25466—2010《铅锌工业污染物排放标准》的排放要求。同时,采用SEM、FTIR、XRD等对碳酸钙改性硅藻土进行表征,进一步探讨了碳酸钙改性硅藻土对重金属的吸附机理。